Ubiquiti Networks UAP-AC-3 Guía de usuario descargar pdf (Pagina 12)

Chapter 2: Using the UniFi Controller SoftwareUniFi

Controller User Guide

Ubiquiti Networks, Inc.

- WEP WEP (Wired Equivalent Privacy) is the oldest

and least secure security algorithm. WPA

™

security

methods should be used when possible.

• WEP Key Enter a WEP encryption key in

hexadecimal format. You can enter a 64-bit or

128-bit key:

Type Hex

64-bit 10 Hexadecimal Characters

(0-9, A-F, or a-f )

Example: 00112233AA

Note: You can use 5 printable characters,

which will be translated to the

corresponding HEX code.

128-bit 26 Hexadecimal Characters

(0-9, A-F, or a-f )

Example:

00112233445566778899AABBCC

Note: You can use 13 printable

characters, which will be translated to the

corresponding HEX code.

• Key Index Specify which Index of the WEP Key

to use. Four different WEP keys can be configured

at the same time, but only one is used. Select the

effective key: 1, 2, 3, or 4.

- WPA-Personal WPA or Wi-Fi Protected Access was

developed as an encryption method stronger than

WEP. WPA-Personal requires a passphrase to connect

to the wireless network.

• Security Key Enter the passphrase that users will

use to connect to the wireless network.

- WPA-Enterprise WPA Enterprise uses a RADIUS

server to authenticate users on the wireless network.

• IP Address Specify the IP address of the RADIUS

server.

• Port Enter the port number. The default is 1812.

• Password Enter the password used to authenticate

on the RADIUS server.

• Guest Policy Select this option to enable guest access

policies on this wireless network.

Advanced

• VLAN To use a VLAN, select Use VLAN ID and enter the

port number.

• Hide SSID Select this option if you don’t want the

wireless network name or SSID to be broadcast.

• WPA Select the appropriate WPA and encryption

methods:

- WPA Mode Select Both, WPA1 Only, or WPA2 Only.

- Encryption Select Auto, TKIP Only, or

AES/CCMPOnly.

• User Group Assign wireless users to a specific user

group. For more information about user groups, see

“Settings > User Groups” on page 13.

Click Create to create a new wireless network, or click

Apply to save changes. Click Cancel to discard changes.

Options

Options vary depending on whether or not your WLAN

group uses Zero Handoff Roaming.

Note: The UniFi AP-AC does not support Zero

Handoff Roaming for the initial release, but it will

with a future firmware upgrade.

No Zero Handoff

Name You can change the name of your WLAN group.

Load Balancing Select this option to balance the number

of clients you specify per radio.

Note: The UniFi AP-AC does not support Load

Balancing for the initial release, but it will with a

future firmware upgrade.

Legacy Support By default, legacy devices, such as

802.11b devices, are excluded. Select this option if you

want to support legacy devices.

Apply Click Apply to save changes.

Zero Handoff

Name You can change the name of your WLAN group.

Radio Select the appropriate radio, 2G or 5G.

Channel Select the channel that all of the APs will use for

Zero Handoff Roaming.

Apply Click Apply to save changes.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 56 57

Comentarios a estos manuales

Sin comentarios

Ubiquiti Networks UAP-AC-3 Guía de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Puntos de acceso wlan Ubiquiti Networks UAP-AC-3